DaierTek Lighted 12V Waterproof Toggle Switch IP67 12 Volt LED RGB(RED Green Blue) 16mm Pre-Wired for Car Boat Marine -3Pack

Really nice quality. Replaced OE switch with the same diameter hole.

I used this switch to operate the courtesy lights for a 1940 vehicle that is wired for Positive earth. The representatives of DaierTek were very responsive and informative in answering questions prior to purchasing. The switch works perfectly with Positive ground vehicles because the LED and Switch portions of the toggle are independent of one another. The Switch is therefore able to be wired to work with positive ground because the Switch is not polarity specific (i.e., the Positive side of the battery can be wired to the ground side of the Switch, and the Negative side of the battery can be wired to the positive side of the Switch). While the LED portion is polarity specific, it is internally separated from the Switch portion of the toggle (i.e., the internal workings of the Switch and LED are independent from one another) so the LED can be wired at the same time using negative earth by running a separate wire directly from the Positive side of the battery to the positive pin for the LED power on the back of the toggle, then completing the circuit by picking up the Negative side of the battery anywhere else in the wiring system (which is not difficult on a Positive ground system). I had previously purchased an intriguing "touch" switch from Ulincos (that also dimmed) but discovered that the wiring (internally) to that switch would not accommodate a Positive ground system (the switch portion could not be wired differently than the LED portion). I am extremely happy with this toggle switch, not only the reasons stated above, but also for the amperage rating for this toggle switch.

Which is worked great and looks great after I installed them but the directions that it came with are totally wrong I had to go with the photos on Amazon product page for the correct install guide... 2 completely different intructions... led portion of switch are triggered by ground not 12v power as shown by instructions that the package came with

Very nice look.I used blue and green at the same time to get an aqua look.Con: the wiring is very unintuitive. The lights use common power of the switch contacts themselves (not just the smaller LED wires). It took a while to get the idea of what was going on.Works fine with my 19v supply. I saw somewhere that 12v to 24v was okay.

The low rating is due to their snafu on the internal LED wiring. The LED colors are true Red, Green and Blue. They are dark in color and also nice and bright. Easily seen even in day light.I was hoping to use two LEDs on a switch to get two different colors depending on if the switch was on or off. I was going to run the acc (+) which is always on when the key is on to the blue to be able to see the switch in the dark, then add green or red to get a mixed color to indicate the switch was on. To do that the LED's would need a negative common. For some unimaginable reason, the designers of this switch used a positive common - making what I desire impossible unless I am willing to add a couple of relays and extra wiring.They do provide nice instructions - but they are tiny. I had to scan it, save it to my computer, then print them out on a full sheet of paper. I have included blown of pictures of the instructions for everyone to be able to see what I'm talking about.Update: They are really nice switches. I went the relay module route, but played with one on my bench and came up with a more simple way to get the job done with a simpler high power relay.The blue LED is passive. If you have blue on and add red or green, you get a bright easy to see red or green. The colors do not mix.I have added a picture of the wiring diagram and below is a link to the easy to use 30 amp relay module. A friend and I have used several of these relays. There is no extra electronics but they are reverse voltage protected on the input and an on indicator LED. The also have top grade connectors. They are only single pole single throw contacts. That is ok for 90% of applications. It just means the contacts close when power is applied. There are no contacts that are closed when power is off.If you want to use several of these switches, I suggest using the Acc (+) to kick on one 30 amp relay. Then instead of the relay in the schematic, wire your load where it shows the relay contacts.CZH-Labs 12V Passive SPST-NO 30Amp Power Relay Module Board.https://www.amazon.com/dp/B00UA3O1IO?psc=1&ref=ppx_yo2ov_dt_b_product_details

awsume 3 colored toggles

these things fall apart so fast its sad. you have to have extremely light hands when assembling them because if you apply too much force trying to push the spade connectors on, the back will pop out of the switch and it falls apart. out of the 3 i bought i only got to install 1 and it only lasted about 2 days before it too fell apart. very cheaply made and not worth trying in anything thats gonna have some rough service life. they will not last. if you can install them without breaking them that is.

I see that some folks are having a bit of trouble with the indicator LEDs. They are counterintuitive, however, the LEDs actually function very well in a verity of combinations.I am using the switches in a negative ground system and switching the ground. I use the blue light for the pilot and the green for active/on. Any combination is possible.