EZDIY-FAB GPU VGA PCIe 8 Pin U Turn 180 Degree Angle Connector Power Adapter Board for Desktop Graphics Card-Reverse Type 3-Pack

Works great. Easy to install.

Don't let some other reviews fool you about these being unsafe. It seems that there are some people reviewing these that understand how to use a multi-meter, but don't really understand how GPU's are powered. Yes, all of the ground pins are common as are the three 12v pins. This is NOT dangerous, and it is NOT a short as these people are implying. It seems they decided to use a single ground plane and a single 12v plane on the circuit board. The GPU only uses 12v and ground. As long as you're getting the proper signal on the proper pins, which all five that I've bought do, you're perfectly fine. If you were finding the ground and 12v bridged... that would be a short, and would be absolutely dangerous. Not a single one of these that I've bought have had a short. You can ignore the reviews saying these are unsafe because the grounds are all common as well as the 12v, and that's perfectly safe for this applications. These people simply do not understand what they're talking about.As to the rest of the product. They do what they do well, they're constructed about as well as you can expect them to be and they look quite good... much better than the majority that just put some foam on the back to protect the exposed circuit board. Above all else, they're safe to use. My one complaint is that there is no latch, which makes sense if the latch is on the inside of the connector as it would be very hard to reach. However, once connected, the connection is pretty snug and they don't back out easily.I'm using a different set on a 3070 Ti and they've been working great. I was using this set on a 3080 Ti, but opted to go with the Thermal Grizzly WireView. Not for any shortcomings of this product, but the way I have the GPU setup and my custom cables, it was pulling on these in a way I didn't like and the WireView is a single block making it more ridged for this application. It's also nice that it can display how much wattage and current the GPU is currently consuming in real time. However, it is quite a bit more expensive.If you need a 180° adapter and you don't want to spend a lot, but you want it to look nice, these are a must. Just be sure that the orientation is correct for your GPU. A lot of people are giving these bad reviews because they didn't read and bought the wrong kit. If you're willing to spend more and you'd like to be able to see the current power consumption, I highly recommend the Thermal Grizzly WireView.

I recently gave up on using a vertical mount on my PNY RTX3090 as the card was running too hot. These adapters do away with the messy cabling that encouraged me to try vertical mounting in the first place. They also keep my AIO pipes away from the hot backplate.

I didn't need this to solve Nvidia connector problems, but thought I'd try the different look of the adapter. They plugged into cable and gpu clean and easy, and the manufacturing quality looks great. It's been 4 months with no issues and I now love the look with no bending cables. The 8pin cables now lay flat against the gpu backplate

The piece wouldn't fit into my or my brothers case, good quailty product. But wouldn't fir our cases.

junk look at the picture, one not completely done, other 2 look at far left pin will not go into GPU or any other plug. Just don't buy unless you like to complete the part.

The EVGA RTX 2070 graphics card in my primary PC requires two power connectors, a 6-pin and an 8-pin. Bending the wires to connect without adding too much stress to the card, plus routing the cables back to the PSU has always been a pain.When I found a SFF (small form factor) build video on YouTube that used these adapters I ordered them immediately. They connect easily to the card, and the connection to the power cables has a positive click to ensure they're seated. Routing the cables is so much easier, there are no sharp bends required, the cables are straight into the adapter.These are available in both 6-pin and 8-pin versions - the 6-pin adapters have both a standard and a reversed connector in the package. The 8-pin adapters have two of the same orientation in the package, so make sure which ones you need - the pictures clearly show which way the pins are facing, so you can determin the right option(s) for your graphics card.I don't review many purchases, but wanted to note how useful these EZDIY-FAB adapters really are, and how much value they provide for their cost. I'm truly suprised video card manufacturers don't include these in their packaged accessories, they are that useful. Super great product, I'm going to buy these for every PC I work on going forward.

I am using these on a Zotac Twin 2080Ti that I've installed a Kraken G12 on, so no backplate when I originally installed these, but wanted to write this review to warn to double check if you decide to purchase a third party backplate from somewhere like V1 Tech. The plate itself is made of acrylic and is fairly thick, so it lifts the other end of the backplate when these are installed with it. For me, I was able to finagle the plate juuuust enough that I don't feel the need to mess with it further, and I really really like what these do for the overall aesthetic of my build.If you're not in this very niche subset of users who will both use these and a V1tech backplate, they work well, and help clean up your cabling if your cables are not the stiffest.I found that the aesthetic was improved mainly because I like the look of straight cables versus curved, and with these you are able to achieve a straighter cable to the GPU.Also of note, these pair well with the Antec All-white cable extensions, which at $35 a piece at time of review, may be a bit steep, but were absolutely worth it in my use case because the actual connectors are white as well versus most other brands that use white cables with black connectors.