General Finishes High Performance Water Based Topcoat, 1 Quart, Satin

Great product. Easy to apply, good protection and nice satin finish

This is by far my favorite poly to use over water based stains and dyes and even latex paint. Now I am a huge huge fan of General Finishes products. By far some of the best stains, dyes, and poly's on the market. In face the only think I dont like about General Finishes products is that I can not find them in stores. You have to plan ahead and order this stuff somewhere online. These days though. All of the best stuff has to be ordered. My being a fan of General Finishes is not why this is my favorite top coat. I would not allow my review of a product to be compromised in that manner. Be advised this satin polyurethane has just a slight bit more sheen than most. With that being said. This is my favorite top coat for numerous reasons. For one. Its forgiving. Water based poly's begin to dry really fast so with most of them if for some reason you brush the stuff on in one spot for to long. You will get this ugly clumping or leave brush marks in the finish. The general finishes stuff dries fast, but is much more forgiving in that manner. It is recommend that you brush the stuff on in a small area then move on, but if for some reason you brush a small area for to long it does not tend to clump up or leave brush marks. Another reason I love this stuff is because it sprays on great with my small compressor and LVLP gun. Many top coats need to be sprayed with a HVLP gun to atomize this stuff properly and get a nice even coat with no runs, but I have an LVLP because I only have a small compressor that only does 5cfm at 40psi. It atomized the stuff properly and I get a nice even coat every time with no runs. My all time favorite thing about this top coat is that I can put 3 or 4 coats of the stuff on in less that a day. This stuff dries hard enough to be lightly sanded in about 1-2 hours depending on the conditions. After about an hour I can go in and hit it with a 220 grit sanding pad to smooth it out and put on another coat. All of the water based or should I say waterborne poly's dry to the touch and can be lightly handled pretty fast, but they will still be to soft to sand. With this poly it is a much different story. Also ones this stuff is dried and cured. It is almost indestructible as far as a polyurethane goes. Even over softwood like pine.

Wonderful product. Leaves wood looking and almost feeling like wood, yet protects it. Ease to apply with a foam roller.

Bought this product to redo my kitchen table and chairs. I bought the satin finish and if I do say so myself it came out fantastic... exactly the look that I was looking for. The finish goes on easy but be sure you let each coat completely dry before you do another. Take you time you will be glad u did.

To cut right to the chase: I am extremely pleased with the results I achieved with this product. I am an experienced "hobbyist" woodworker but still get apprehensive with the finishing stage of a project. The GF finish allowed me to achieve my goals: a satin finish on a maple cabinet top with no yellowing or color change. The cabinet top is a glued-up maple panel approximately 55" x 15". I sanded it to 320 with a Bosch random orbit sander prior to applying any finish. I cleaned up the sawdust after sanding and between coats of finish with a tack cloth. I sanded and finished BOTH the top and bottom of the panel. I did not count the number of coats, but three was not enough. I am guessing I stopped at eight coats. For the first half-dozen coats I used the finish straight out of the can, after mixing thoroughly (required to get the satin particles off the bottom of the can, I would say 5 to 7 minutes of stirring with a small paint stick). The last couple coats I thinned the finish quite substantially after pouring the needed amount into a small paint pail. Since the finish in the can is of a milky consistency let me use a milk analogy: think of what's in the can as the consistency of the half-and-half you put in your coffee. My last couple coats were the consistency of skim milk with a little water added. I found that the thinner final coats allowed the brush marks to relax quite a bit more than in the thicker coats. I would recommend thinning for the final coats; if I was doing it over again I would probably use the out-of-the-can consistency only for maybe ther first two or three coats and then start thinning from there. I used a good "traditional" paintbrush, a Purdy Nylox "Dale" model (soft bristle) with a beveledf tip, 2-1/2" wide. GF recommends a foam brush. I can't comment on this as I did not try it, but for sure the brush marks were my biggest issue. This is why I attempted the thinning (successfully, as it turned out) described above. I am not a fan of foam brushes but would have tried one had the thinning not worked. I sanded between coats using successively finer grits. 320 on the first couple coats, then 400, then 600, 800, and finally 1000 automotive paper prior to the last couple coats. As others have observed here, this finish dries completely quite quickly. In my case I left most coats to dry at least 8 hours and by that time the sanding produced a fine white powder with no stickiness at all. This was easily cleaned with a brush-equipped shop vac followed up by a tack cloth. (BTW I did use the cheapie oil-based tack cloths you can pick up at Lowes with no oil-vs-water problems.) I also used this finish an a couple of maple plywood shelves with solid maple edging for the inside of the cabinet. No issues here either and the color is completely natural. I also put a coat of Butcher's wax on these shelves maybe a day after the last coat - worked great after being buffed out with a wool pad on the Bosch random orbit sander. Will probably do this to the top eventually as well. The things I would be most careful to look out for are BRUSH MARKS and DRIPS. I addressed the brush mark issue by thinning the finish. All of my surfaces were flat and horizontal so it was pretty easy to avoid drips. I could see this being a bigger issue for vertical surfaces, so be careful if you have those or any detailed carvings or turnings. Very easy cleanup with warm water and a touch of True-Green cleaner. I stay away from hand soap for these kinds of things as those often contain various oils. I found little or no VOC or odor with this finish, another significant positive for my in-home (basement) workshop. It goes without saying that this finish is relatively expensive compared to the Minwax at one of the box stores. But the bottom line for me, again, I got what I was after which is a nice satin finish with a natural color maple cabinet top. Would definitely use this finish again.

This milky white satin varnish performed well and since it’s water based the clean up was easy.

It’s a great topcoat, way bette than other brands. If you use spray gun applying it, it is butter smooth. Please remember to add 15% volume of water to dilute it if you choose to use spray gun to apply. Otherwise it will clog the Spray gun tip.

I was looking for a topcoat for a mahogany piece that I had bleached and did not want the wood finish to darken it. This topcoat maintained the bleached/natural look of the wood and was easy to apply. I also did not need to apply a lot. Expensive but worth it.

Again excellent finish when applied to rollered paint using foam brush

Good coverage and good product

Love it

Works great. Put the flat finish over black advance paint front BM. The 2 pieces I did look great. Toned down the shininess but did not turn it totally flat. Came quickly