2Pcs Pressure Relief Device for Triton, with Disc Seals Cover Valve, Shower Spares Parts Compatible with Triton Electric Showers (Replace of 82800450)

Works fine

Turns out that when using a fancy high-pressure shower head, it's a good idea not to turn the shower to maximum flow (even if it's for cleaning out a litter tray) or the back-pressure blows the relief valve... Slightly embarrassing. Fortunately, other than the instructions online being for the wrong flavour of Triton (which left me disconnecting things to look for a wire that didn't exist), this turned out to be an easy fix - I'd already discovered that the valve was there while trying to work out why my shower was leaking a month before.Quick fix (give or take reaching to invisible screws while standing in a damp bath), came with all the necessary bits, any inconvenience came from the design of the shower, not the replacement relief valve. I was a little disappointed that the original one didn't continue working when the ball was put back in, but since the replacement turned up so quickly it wasn't a big deal.Also turned up quickly, which was helpful since the shower wasn't working...

I was using a changeable shower spray head and accidentally turned it off. This causes a rubber safety pressure to break open. Easy to fit. Turn off electricity. Remove shower front with 3 screws. Where the shower head connects this valve is held in by 2 little screws. Very easy to swapBUTTHIS IS IMPORTANT - KEEP THE OLD SCREWS ON THE VALVE.The screws supplied with the part are 100% to small. Use the old screws and you will be fine

Several years ago the pressure safety value went on my shower, so I bought a new shower. Recently I got a new shower head for the shower that has an off switch on it. This ended up blowing the safety value on the newer shower. So I looked up google to see how I could fix it and it just said buy a new value and install it, it's literally a 5 min job if that. So ordered these as you get two in them, so I would have a spare ready to go when it inevitably pops again. The valves are designed to protect your shower unit from bursting due to build up in pressure, it pops a small ball bearing out when pressure reaches a certain level.Installation was very simple, unscrew a couple of screws on the top and bottom of the shower unit and remove the front cover. The old valve will be sticking out the bottom near the hose, it's held on by two screw, unscrew those and then screw the new valve on, replace the cover and screw back on. It's that simple, you don't need any plumbing experience or to be an electrician (but I would recommend turning the shower electricity supply off just to be safe). Had the new valve in for last few months now and all is good with the shower (just had to tell everyone to not use the switch on the shower head to stop the water!)

Great little bits . Easy as pie to fit . And you get two what more do you want. Shower should last another year or 2 with 4 adults using it daily.

Had water dripping from the shower unit. The cause of this was the shower head had become scaled up and hence this prv did its job. Fitment is easy. Turn the power off to the shower 1st. Take the cover of the shower and remove the the black prv using the two little screws. Probably didn’t need the supplied black plastic elbow piece as the original was okay. It was just the small round black rubber cap / membrane that was needed and this simply pushes onto the black plastic elbow. Reassemble and the job is done. Probably took less than 5 minutes ! In hindsight I only needed to buy the black round push on covers. I now have 3 spares should this happen again,which I left inside the shower enclosure for safe keeping. Although an expensive purchase for a very low cost piece of plastic, costing pence to make it was far cheaper than a new shower or a triton engineer visit.

Good delivery but it does not replace the original white device because the fixing holes are too small. The supplied screws are of no use as they are self tappers. You have to use the original white device screws to fix as they are threaded. I re drilled the holes and fixed the new device in place using the original screws. All seems to work ok. Beware however of the fact it is not a straight change.

Repaired shower for small price, now working well.