Size:2 gallons ComposiMold’s Clear Epoxy Coating for Wood, Art, Sculpture, and Castings Specifications Comes in several different sizes : 8 oz (2, trial size 4 oz bottles), 16 oz (2, 8 oz. bottles), 32 oz (2, 16 oz bottles), and 2 gallon size (2, 1 gallon bottles). The sizes consist of ½ epoxy resin and ½ hardener. This is epoxy resin is designed for use as a coating or filler resin for wood, concrete, table tops, bar tops, art, and more. For resin coverage, when poured at room temperature, the resin typically settles at approximately 1/8th of an inch. Higher temperatures will make it thinner. Do not use below 65 F temperatures without warming it first. At 1/8th thickness, 4 oz. will cover about 2 square feet. 8 oz. will cover about 4 square feet, 16 oz. will cover about 8 square feet. 32 oz. will cover about 16 square feet, and 2 gallons will cover about 128 square feet. You can use a brush to spread the resin thinner for lighter coats. 1:1 mix by weight or volume, low viscosity for easy pouring and reduced bubble formation For excellent finish with low bubbles: 1.Mix the two parts very carefully. Pour the Part B hardener into the Part A Resin by pouring down the side of the cup to eliminate bubbles from getting into the mix. 2.Stir gently and slowly 3.Warm the resin to about 80 to 85 F prior to mixing, but be careful as this will decrease working time to about 25 minutes, and it will also reduce the viscosity so bubbles will come out. Give the resin a few moments before pouring. 4.Use a heat gun on the surface after you pour to reduce the surface tension so bubbles can break apart. Do this every 10 to 15 minutes to make sure bubbles are gone. The low viscosity makes it excellent for jewelry castings, figurines, and more.
H**Y
I must have received a bad batch...
I followed the instructions exactly, temperature at 80F, mixed exactly 1/2 ounce of each, stirred gently but thoroughly (for about 5 minutes continuously,) poured it on my workpiece, and three days later still a goopy mess. Tried several small splotches with a little more hardener, a little less hardener, etc.. and several days later, all of the splotches are exactly the same, sticky syrupy blobs. 80F and 32% humidity the entire time.
F**.
This is my second batch and I’m happy with the quality
I’ve seen higher prices for what appear to be identical products. This is my second batch and I’m happy with the quality. I purchased for an artisan to finish coating some musical stage equipment, and so far so good!
A**R
Perfect cast every time
Thank you for this! I'll for sure be a repeat customer. I use these to make little models for alcohol inks and such and this resin so far has been perfect. Hardens quickly and so far no gooey parts.
K**3
Two Stars
no luck with this
R**A
Too Liquidy
Masking tape did not hold it from seeping through to good wood>
A**R
I like it
The only reason I didn't give it 5 stars was because I have never used epoxy before, therefore, I have no way to compare it. I think it is great! It cures fast, and is easy to use. It is very clear and makes some very nice pieces of jewelry. I have been playing at mixing it with powdered pigments and pouring it into silicone bezel molds, then filling the space with various objects. These pieces are gorgeous. I am about to order it again so I don't run out.
L**N
This is my first time using it and it was easy
I used this both in resin molds to make keychains; there were some bubbles but this is my first time working with resin so I'm not sure if it's me or the mix. Didn't have any problems getting them to set.I will say there are limited instructions.
S**N
Came quickly and just what I expected
Came quickly and just what I expected
Trustpilot
2 days ago
1 day ago