eSUN PLA+ Filament 1.75mm, 3D Printer Filament PLA Plus, Dimensional Accuracy +/- 0.03mm, 1KG Spool (2.2 LBS) 3D Printing Filament for 3D Printers, Pine Green

No issues, fits, prints perfect, no breaks, nothing. Just works perfect with the PLA temperature default settings in 3d printer I have. It was sealed air tight went sent and the color is perfect.

eSUN PLA+ has become my go-to filament for most of my prints. I mainly design functional parts for use in tooling and fixtures and have never had any problem with the structural integrity or dimensional accuracy of this PLA+. I have run through dozens of rolls of black, grey, and fire engine red with no issues. I don't follow any strict climate control processes or store the rolls in any particular way. I try to remember to remove the filament from the AMS gearing when I don't plan to be printing for a little while, which I believe is a good practice. I always check the end of the filament for brittle arears before loading into the AMS and snap off the end by hand until I run into the first part of the filament where it just bends back and forth in my fingers. That's typically just an inch or two from the previous end of the filament and I never have any issues following this process. I'm more concerned with accurate prints that have great layer adhesion, so I don't typically print for speed, but I have no reason to believe that this filament could not be pushed to limits that I have not tested. Affordable, reliable, and consistent - I count on eSUN PLA+ to get the job done.

So far the best pla I’ve bought. Decided to try a brand that was directly supported by bambu and thought what’s a few more dollars for plus if I have less failures. First benchy already can tell the build just looks better has a shine to it almost and just better quality and experience from the get go. The red is a rich rich color and couldn’t be happier with it. Definitely worth the increase in price, don’t cheap out you save money in the long wrong not having repeat failures and spaghetti. I will definitely be replacing my other filaments with this brand and plus where available! Note: this is the first time I’ve ever been able to clearly read the benchy text on the bottom.

I’ve used a lot of different PLA+ brands, and eSUN continues to be one of the most dependable options out there. The filament feeds smoothly with zero tangles or breaks, and the diameter consistency is spot-on, resulting in precise, clean prints every time. Layer adhesion is excellent, and the surface finish comes out beautifully glossy without needing any extra tuning. This PLA+ also has great toughness compared to standard PLA — parts feel stronger and less brittle, perfect for both functional prototypes and aesthetic prints. It sticks well to the bed without warping, and cleanup after printing is effortless. If you want a filament that performs well across different printers and print speeds, eSUN PLA+ is a solid choice. Great value for the quality and reliability!

Nice print quality as well. Not quite as good as Bambu, but definitely a top 3 print quality for PLA for me.

I’ve already gone through 6 rolls of the stuff and it’s been great. The only reason it’s not five stars is because every once in a while you’ll likely get a spool that isn’t wound very well so you have to sit there and make sure it doesn’t catch on itself and ruin your print

Nice printing, no problem great color an adhesion to platter, no clogging and has a light shine. Recommend this filament-- used the eSun for head and body pleased with the results

I bought two spools. The first one was pretty great out of the package, although not all that evenly wound. Then, around the 80% mark it started popping and hissing, something I’ve never experienced because I’ve never used cheaper filament. The filament was wet, and it was bad. I used the rest of the spool and tossed out the remainder. My print was pocked and bubbly on the outside because of the popping. So I moved on to the next spool. It was ok for a while but got tangled on the first print. Wasted about 6 hours of time and filament on that one as it was only halfway through and now way to fix it. From then on it was just a mixed mess and would only print properly for two hours at most and then either snap, clog, sizzle, or not print correctly. I wanted to like this filament, but this was mostly a waste and a massive headache. This filament has caused more problems than other filaments I’ve bought over the past four years combined, but the last one was the one I didn’t much care for the most. The filament snapped and completely jammed my extruded. If I would’ve trusted this filament and left my house like I intended I would’ve come home to a messed up extruder and possibly a burnt up motor. I was only outside for two minutes and I came inside to check and the extruder was clicking and the motor was HOT. I stopped the machine, I tried to take out the filament to no avail, and then completely disassembled my extruder to find segments of filament inside it and the upper and lower cap bowden tube. Never seen a failure that bad. I don’t recommend this filament if you’re using a printer that prints fast 150mm/s+ because things can go from bad to worse very quickly. I’ve only had issues with moisture from PC, never any kind of PolyA+, and never had breakage issues like this. It was very upsetting and I had high hope from others recommending this brand and type.

Works a little bit less good than bambu lab pla but that is expected with the a1 mini. Is cheap for it's quality!

Das Filament in Knochenfarbe macht bereits beim Auspacken einen hochwertigen Eindruck. Die Farbe ist angenehm dezent und wirkt natürlicher als reines Weiß, was besonders bei Deko- oder Prototypenteilen gut zur Geltung kommt. Beim Drucken lief das Filament sauber und gleichmäßig durch den Extruder, ohne Verstopfungen oder starkes Stringing. Die Layer haften gut aufeinander, wodurch stabile und optisch saubere Druckergebnisse entstehen. Die Wicklung auf der Spule war ordentlich, was ein ruckelfreies Abrollen ermöglicht. Im Vergleich zu normalem PLA wirkt die PLA+ Variante etwas robuster und weniger spröde.

جميل اللون نفس الصوره

Filament works well. Good adhesion and few failed prints. Strength seems ok. I've had problems in the past with pla filament that breaks in storage if placed under any strain, e.g. if you thread the end through holes in the spool to stop it unwinding. This pla+ seems to behave better.

fungerar jättebra