BestEvMod2025 Upgrade Rear Bumper & Trunk Sill Cover Protector Bumper Guards Compatible with 2025 2024 Refreshed Tesla Model 3 Highland (TPE Version)

The Cybertruck comes with Glass-filled ABS bumper covers. This material is very tough but is not as durable as bumper covers from other manufacturers. They don't even have padded areas on top of the bumper to protect it from scratches caused by standing on it.These stainless steel covers are the answer! The fit perfectly over the top of the bumper and curve around the corner to protect the top edge unlike others. I'm not sure if the finish is a powder coat or a paint but it is very durable. As you can see in my pictures I don't baby them.Installation is a breeze using the pre-attached 3M tape.Installation tip: use the tip of a box knife or other object to release a corner of the tape's protective cover before proceeding to make it easy to remove. Trying to remove the film with your fingers will be a frustrating endeavor ;). Once you have corners of all pieces lifted, you can remove them at once and install the covers.As I said in the headline, these are a must-have.

It's a shame the normal cybertruck doesn't have anything like this pre-installed from the factory. When I saw these available, I had to give them a try. Great fit and finish, but I will say, it took me forever to peel all the tape off. Maybe there's a better way but the tape is so sticky that it's difficult to get it off. Especially since there is so many pieces. Still worth the hassle and it looks great. Hopefully it stands the test of time.

The bumper protector looks really good and I think it adds to the overall aesthetic of the truck. The only issue I have is the rubber gasket the protects the edge of the bumper guard is not attached firmly and likely will fall off with any amount of use.

The overall design fits well with the 24' Model 3, however some minor issues keep it from being a better product.In shipping, it's folded tightly in half resulting in a significant crease in the middle which prevents that section from lying flush.The cut could be better. I find the edge just doesn't get far enough under the weather stripping and the flap into the trunk a little to bulky. It fits with my 3D mat but barely.The adhesive for the Velcro is low quality and melted in the heat. The Velcro is stronger than the glue so if you try to reposition the cover you may need to get some epoxy for the Velcro strips as they will come off.

The cover protector fits perfectly on my 2024 Tesla Model 3. It's good quality and looks like it belongs. Before installation, just leave it in the sun for about 15 minutes to help it align properly.

The plates are not straight. They stick on one side and tends to be bend on the other side. Even with additional 3MM tapes the plates don't hold to the truck. Strongly recommend getting wraps than getting steel plates as the fits are bad and can't even return it as 2 of the plates flew away while driving on the highway. Don't recommend at all.

I'm very pleased with how good these protectors look installed. Matt Black is more satin and goes well with the other black finishes on the rear of the truck.All of the outside edges of the protector segments wrap over the edges of the bumper where I was most worried about wear. Installation was simple, with strong doubled-sided tape is already fixed to the protectors.A little patience is required to lift up a corner of the protective film on the very sticky double-sided tape, but very sticky is a good thing.I won't know for a while how well they hold up when being stepped on, but I'll edit this review later to include that factor.

This fits great. I also use the JawJut carpet liners. It all matches well.One thing to be aware of. the tesla back door latch has a plastic cover (same material). I could not get it to close reliably if both the bumper and the latch cover were in place.I just took the latch cover off...

Leave it to Tesla to cost cut so much, that they would remove the protective sill from a high wear point of the trunk. Great idea to just put a thin layer of fuzzy carpet that will get scraped up and ruined quickly...This is a necessity for everyone. It's built well, it's durable, and it's easy to install. It does come folded in half so pro-tip, open it up and hit it with a hair drier or heat gun for a while before installing. Get it warm and soft. Any creases will be gone and it will be pliable and conform to the trunk sill for a super clean install that fits like a glove with no areas lifting or contacting improperly. Mine does not budge at all, has an accurate and tight fit, and works perfectly with my trunk mat.Would recommend. Thanks for fixing what Tesla was too cheap to keep.

So glad I got this for my trunk. Will protect the carpet and my trunk liner. Has a strong Velcro which will hold the protector in place.

very suitable

Fits perfectly and matches the Tesla all-weather rear trunk liner.