Cable Matters 8-Pin GPU Power Cable, 6+2Pin PCIe/GPU, 2ft | 8-Pin PSU(EPS/ATX) Male to Male, Graphics Card Power Cord, Compatible with Corsair Type 3/4, Not for EVGA PSU

Worked on my corsair PSU. It is what it says it is.

Thankful ChatGpt recommended this to me because it fixed my pc randomly shutting off. Turns out the electrical output from my PSU couldn’t be daisy chained due to power shortage and I’m excited to say this worked.

It fits perfectly on my card. Is a high quality cable. It is kind of tight on the plug on my power supply. I got it to work though I haven't had any issues.

This was for my ex partner

I usually like Cable Matters cables but this one was disappointing. I was a little thrown by the fact that one pin on the RGU side didn't have a contact but upon doing a little research online, found out that this is normal for Corsair PCIe cables. The two far pin receptacles are "sense" pins and you only need one of them. Unfortunately that was where my good fortune ended. Both ends of this cable are extremely tight and hard to sit into the sockets. The original Corsair PSU plugs slid in easily and locked with a click. But that wasn't the worst of it, after plugging one end of this into an open PCIe socket on the Corsair 850x and then the other end into my 5070ti alongside the other two cables that the GPU requires when you use the adapter, my computer wouldn't boot at all. I did a variety troubleshooting steps - testing the PSU, unplugging and letting it reset, putting the old gpu back in and even running with only the built in motherboard Intel GPU. I left the cable plugged in because it wasn't being used for anything. The computer just wouldn't boot or even start. Finally I had a thought and completely unplugged this Cable Matters cable. Voila my computer started right up. So TLDR, the cable has a fault or is shorted in some fashion. I see others have had similar issues so I would probably avoid this cable.

Worked perfectly and didn't feel cheap and thankfully not the god awful ketchup and mustard colors some PSUs have.

This is exactly what i needed. Everything works perfectly, no issues at all.

I purchased these cables to use with a Cooler Master MWE 850 Gold V2 (Model MPE‑8501‑AFAAG‑US). Finding replacement cables for this PSU is difficult since Cooler Master no longer sells them, so I did quite a bit of research on the V1 vs. V2 pinouts. Everything I found indicated that the MWE Gold V1 and V2 use the same pin configuration, and even though this seller doesn’t explicitly list the V2 as compatible, the cables should work. After receiving them, I inspected the wiring and verified the pinouts against a known‑good OEM cable. Everything matched, so I installed them — and they worked perfectly. For the price, this is a great alternative to having custom cables made. My only reason for giving 4 stars instead of 5 is that these use 18‑gauge wire instead of 16‑gauge like the OEM cables. It’s still safe and functional, but it would be nice to see the manufacturer match the original wire gauge.

玄人志向のKRPW-GS750W/90+には使えませんでした。 テスターでピンアサインを調べましたが 全く違うので挿して電源を入れると最悪グラボが壊れます。 物の方は問題なく、 電源側、グラボ側双方共に問題なく入り 問題なく外すことが出来ました。 特にカプラーは入らないより外れなくなる事の方が危険なため 入れるときに無理な力が掛かる様なら 挿さない事が賢明です。 結果的に使えませんでしたが 物は問題無かったので星は5です。

The cable works as expected, but make sure to check the pin layout of your PSU. I’m using it with an MSI 850 GL PSU without issues. looking at the cable extremities, On the PSU side (8-pin), the layout has three 12V pins starting from the lower left, plus an empty pin on the bottom right; the remaining pins are ground. On the GPU side (6+2), there are three 12V pins on the lower left, with the rest being ground. I recommend comparing this arrangement with your other PSU cables to ensure consistency.

det blev jätte fint

Works great with my old Label corsair hx1000i. Just make sure the pinouts match and you'll be fine

Très bon câble, comme l'original, il alimente bien ma 1080. Par contre je le trouve un peu chère, qui que la longueur et la qualité de fabrication soient bonnes.