GSCIT Club Melamine Edge Banding, 1 1/2 Inch x 10ft Black With Hot Melt Adhesive Pre-glued Flexible Edging Trim for Plywood Cabinet

I purchased this when remodeling my kitchen to update my cabinets. They are older and had no trim on the edges. This stuff made them look new! It was so easy to use and made such a difference in the appearance. It’s been months since we used it and it still looks beautiful and has not broke loose. We applied it with a small heat gun and then trimmed any excess that needed it. I have also used this trim to redo a cabinet that was bought years ago and the trim had broke off and you can not tell the difference between the factory door and the one we replaced using this product. The adhesive works well and the price is great!!

The media could not be loaded. The product came as advertised, It had no colored variances, solid matte black throughout with no breaks. I would recommend a low to medium heat setting on your iron when applying, this product is made of plastic and has the potential to melt. The glue performed fine and stuck well, I had no problem taking off a small spot and reapplying it without damage to either item. Cleaning the excess glue was easy it just wiped off. It seems to perform well it doesn't scratch easy and I expect good durability out of it. Installation was quick and simple Just a simple iron on with low to medium heat and you're good to go! Good value for the price I would buy it again.

The media could not be loaded. I bought an Ikea bookshelf to diy it into a pull out pantry door next to my fridge. It required me ripping the shelves down the middle leaving exposed MDF in edges. I planned to paint it but did an amazon search for alternative options and found this tape. I am not a professional so there are lots of oddities, like the shelves not winding up the same width, and of course MDF chipping from ripping with a saw. But back to this tape. No instructions came with it, which I was prepared for based on the reviews. I used my household iron and that there was some residue transferring onto the tape, and it looked terrible. Luckily, I was able to scrape it off and try again. I decided to use parchment paper as a barrier as I ironed on high heat. I had much better results. Also, nonpro tip: don’t try to tack one end then the other, then iron the middle. I found out again that the taoe stretches as you iron and caused a pucker in the middle, which puckered a bit. I was able to mostly iron that down to where it was acceptable without scraping that off too. About an hour total time and I covered 5 shelf fronts and two sides. It looks acceptable and I am happy with it. I may paint the chips or seal it with silicone calk. Overall I am happy with it. 4 stars since there are no directions n which would have saved some waste.

I made some pullout kitchen drawers, and needed this for finish the edges. This edging works great -it's color matched, and applies very easily.I try to be precise in measuring, cut once, and minimize waste. But of course it's better to cut these a little long than a little short. Then if you've got a little overhang, just take a sharp pair of scissors to trim that off.Once heated with the iron, it sticks pretty fast, but if you mis-appply it, you can just put the iron on again to soften the glue and reposition.I bought the width trimmer on Amazon, as well. That's kinda tricky, and takes some practice. It's almost worth putting the edging on a scrap piece so you can see how it works so you don't mess up your actual finished piece. You gotta squeeze the trimmer, but not too hard or it bites too much and tears the edging.

The media could not be loaded. The best thing about the product is that you can reapply heat at any given time to remove, move, apply, straighten out, etc..Two things it’s super brittle when it’s dry, so if you try to jump rope with it, it’ll probably break and it’s super flimsy when it’s hot.Only thing I would recommend is if you were product is a different width than the actual edge than you have to shave it off and I’ve done that with the razor blade but they have a tool for that

Installation with a home iron works perfect! Really added the finishing touches to my melamine board pantry and will be using for custom closets in the future!

Got this trimmer today just in time to do some trimming but i am using 3/4 maple plywood and the tool does not want close that small but the description of this trimmer claims to be able but it does not .As a single sided trimmer works really well, what took me hours and lot of swearing, now it took minutes and is super easy.the seller says to E-mail them but what is your e mail i could not find it anywhere.

The product came on time, matched my materials (White) and was easy to install. I used a double sided cutter and there were no tears or issues. I suggest that if your banding 3/4 material to order 7/8 banding. That’s what I did and it worked perfectly.