LimbSaverClassic Precision-Fit Recoil Pad for Wood Stocks

excellent pad.I was looking for a replacement recoil pad for a Remington 7615 with the standard non-pistol-grip stock.my understanding is that limbsaver made the original recoil pads for the Remington factory for the 7615, and there appears to have been some type of defect in the pads 'materials' at that time in that they turned 'gooooey' - as did mine.The 7615 has not been made for several years so they are not listed in any fitment specs in any recoil pad catalogs.since the original recoil pads had been made by limbsaver (or so i read) i looked at their online fitment pdf, compared dimensions of pads, printed a page or two of ones i thought might be a match, matched up the end of the 7615 for size and screw hole alignment with multiple pad images (with the old pad removed), and then found this pad : # 10102it looked to be a perfect fit for the 7615 with the standard non-pistol-grip stockso,ordered it;installed it;and YES, the #10102 is a perfect fit.not just close, but perfect.writing this review to help anyone with a 7615 with the standard non-pistol-grip stock.SIDE NOTE: several reviewers for limbsaver pads, noted poor fit when they ordered a model based on the fitment descriptions for the limbsaver pads. To prevent such problems YOU SHOULD consider going to the limbsaver site and view their PDF that shows the pads and their sizes. print the relevant page with the pad you think would fit (and as explained for print sizing), cut it out of the page, remove the existing pad from your firearm, and then see if the cut out indeed fits for size and screw hole alignment. this is the only way to prevent any fitment issues.

I bought this for an 870 Express 12 Gauge Magnum with wood stocks circa 1989. I use this primarily with hard kicking magnum turkey loads which can be punishing. The fit is perfect even though the chart does not show my model. I used the sizing chart provided on the Limbsaver web site to check the size and it was right on. No gaps or overhang/underhangInstalling this is easy. Best to add some dish soap to the screw holes to make inserting the screwdriver and removing the screws easier on the old one. If not, you will chew up the old hard rubber on the old pad. Same thing for installing the new pad. A little dish soap and everything slides together with little effort.I have used other Limbsaver products and it works to rreduce the felt recoil by absorbing the initial impulse. Other have noted that the rubber is tacky, and it can drag on fabrics when you pull it to your shoulder. Especialy cotton garments. Less so on synthetic or polished fiber shirts and jackets.This is an easy and efficient upgrade to any hard kicking long gun. I recommend it.

I’m not going to return it, but the fit is slightly off in some areas, either too much material or too little. Some areas it’s flush. I see they have a 700 option on the limbsaver website, but this says it’ll fit too. I went with this one, it’s not worth returning but it’s not quite perfect.

Excellent recoil pad. Makes a huge difference over the original. Put this recoil pad on a Panzer Arms PA37. It’s a Turkish clone of the Ithaca 37. The dimensions of the pad fit the Panzer stock perfectly. The screw holes are slightly high for the Panzer stock, but after using the dremel and a little customizing the fit is near perfect.

While it isn't listed as a "fit" for the 10601, I ordered one based upon the template. It fit my 12 ga Weatherby Orion Sporter O/U perfectly. Couldn't be happier. Appears to have considerably more cushion than the original which had hardened appreciably over the years.

I bought this for my Remington 1100, model year of 1968 with a Woodstock and a slightly curved rear back plate. That curve is typically peoples bane, some people will saw their shotgun flat to get these things to fit or resort to other means. No modification to the gun is necessary. The chart on the manufacturer‘s website will actually point you to the wrong part number if you have one of these older guns with the curved rear would stock. After calling Limbsaver tech-support pointed me to model 10800 for my shotgun. Now this model will only be dimensionally perfect with two exceptions that you will have to make The following alterations on your own: 1: only the top screw hole will line up perfectly you will need to drill a new bottom one with a quarter inch drill bit, again you’re drilling this hole into the limb saver not your firearm, I never modified my 1100 in anyway I just put a new hole into the recoil pad and you can’t even tell him the final product. 2: The model 10800 is flat and won’t fit the curve of the wood out of the box here is what you do, you will place it in a pan of boiling water and heat it for about five minutes, I then pulled the recoil pad out of the boiling water with tongs and immediately into a towel, Grasping it from both ends with the towel while it’s still hot bow the recoil pad, It will take firm and even pressure but you don’t have to muscle it too hard. And it’s easy to go too far you only need to add a very slight bow. Keep checking it against your 1100 and when you have the perfect curve simply attach it Using your new lower screw hole and stock upper. Surprisingly I got it right the first try, like I said don’t add too much curve it looks like you need more than you really do. As you can see from the attached pictures it does not stick out anywhere, top, bottom, sides, The model 10800 matches the width and height of the wood perfectly you just need to add the slight bow if your 1100 has the curved rear plate. I’ve been all over the Internet and I’m almost convinced that I’ve got the first working solution with this procedure!

The pad looks like it will definitely help reduce recoil, also seems sturdy to maintain accuracy. Have not had a chance to head to the range yet.Only con about the product, It is slightly wider in one area and shorter at the bottom for my Savage 110 wood stock. According to Limbsaver website, it should be a perfect fit. The difference is barely noticeable from far, but it still serves it's purpose. I tried many different templates, and none were "exact fit" even if limbsaver says it will fit. It s to be expected since it is not a grind to fit.

Works great! Feels like I'm wearing a thick, soft gel shoulder pad when I'm not. I'm using it on a Beretta 1301 semi-auto and it's a world of difference. The length of pull is longer, but a bit of practice got me used to it. Exact fit and super-simple installation with a screwdriver, nothing to it. Price was good and it arrived fast. I'll check out this vendor again.

Easy to fit. works great, reduced recoil tons.

limb saver is the my favorite to install

I bought a real expensive shotgun with a granite recoil pad, piece of crap it came with. I put this recoil pad on and it feel like a dream. I used 3.5” slugs to test it and it feels like my .243 , WOW!!!!