Printhead Cleaning Kits Inkjet Printers, Printer Cleaning Kit for Epson Ecotank Printers, Printer Cleaner Kit for HP, Inkjet Printers Head Cleaning Solution for Canon Brother Print Head Liquid Nozzles

I tried printing a copy of a printer purge file that had all colors and check which color was having a clog. Two colors had a 100% clog. I tried printing several times with the same result. Then did a light head cleaning (3 minutes) and that did not work. Stoped doing the 7 minute clean up until I tried this product.I reluctantly purchased it as a last option before I gave up on the printer. Was already looking for new printers. When it arrived, i was ready but my ET-4700 did not readily lifted up to get to the printer heads. You have to remove two little screws right above where the printed page comes out. Then the top part goes up and you have full access to the printer heads.You have to put something to keep the top of the printer opened. The next step is to put paper towel right under the printer heads. You have to fold the paper very tightly as there is not very much clearance between the printer head and the bottom of the printer. The syringe can eject 5mm at a time. This is good so that you don't flood the bottom of the printer. The bottle comes with 100mm and it is recommended to flow no less than 20mm into each color head with a possible clog.After the paper towel is in placed between the printer bottom and the printer head, you have to gently take the soft plastic tubes out of the cassette (a little reservoir box where the ink passes right before it prints to the page) that sits right on top of each printer head.You have a choice to make as to where you plug the tube that comes out of your syringe.1st Choice: Place the syringe tube on the same place as the soft plastic tubes that flow the ink from the big reservoir.2nd Choice: Remove the cassette (a little reservoir box where the ink passes right before it prints to the page) that sits right on top of the print head and connect the syringe tube where the cassette makes contact with the print head.I chose the first one as it seemed the most thorough option. The videos I saw stat that it is almost always right on the head but I though why not clean anything in the cassette as well. Plus the syringe connection to the print head did not all that tight (worried about leaks).We did 4 flows (as the syringe has 5mm) for each troubled color (we had Yellow and Cyan with a complete clog). I had to be careful when i replaced the plunger after I filled the syringe with the clear fluid that came with the product. The plunger seems to have a very tight seal and I was afraid of shooting the liquid really fast as I replaced the plunger.After you shoot 10mm of liquid; move the head towards the other side of the paper towel to get that side ready for the other 10mm of clear liquid. If you see the paper towel completely soaked in ink. Then replace it. I recommend using the gloves (plastic bag material) that came with the product of use your own nitrile gloves. The paper towel will be very saturated with a clear solution and remaining ink. Move the head to the left or right and remove the paper towel. Use another paper towel for the next color but if you see too much liquid, clean the printer bottom before moving to the next clogged color.We only had two colors to do so, we used a few more paper towels to clean the bottom of the printer when we were done. Replaced the soft tubes that go to the cassette (gentle and slow proces) the tubes felt pretty delicate.We went ahead and did the full printing head clean regardless (7 minutes). You have to turn the printer off and then hold power button + help button for a few seconds to turn on into full cleaning mode. I had full ink on the tanks before I started this process and then seven minutes later I saw that all had gone down, mostly the black ink for some reason.Test post-product:Printed the head alignment page and surprise!! I SAW ALL FOUR COLORS in all their glory!Then printed a personal document and it was perfect.Very good product and resulted just as intended. Will definitely have this on hand and also use the printer more often from here on.Satisfied Customer.

I recently tried to print some MTG proxies on my Canon G3260, and they all came out overly blue. A nozzle check told me the yellow was clogged. I first tried a nozzle cleaning but that didn't help. I watched a YouTube video to get other ideas and discovered that this particular printer should be easy to unclog myself, but I'd need a nozzle cleaning kit. So I found this one on Amazon.After receiving the kit I followed the steps in the video to unclog the yellow. While I was at it I also cleaned the cyan and magenta nozzles. I had to squeeze 3 or 4 syringe fulls into each nozzle, until the expelled solution ran clear.I dried off the ink mess I made on the printhead, and let it dry a few hours. I inserted it back in and did the nozzle check. None of the 3 colors printed! Next I did a deep clean - all three colors showed up, but they were faint. An ink flush was done next, which took 6 minutes to run, only to end up with still faint colors. Finally, another deep clean - the full colors came back! I printed the proxies and they came out great!Lessons learned for next time: wear the included gloves, and do the cleaning in the laundry sink. It's a messy operation, and the ink does stain skin! Also see if there's a kit with a larger capacity syringe, so I can clean each nozzle in one shot. Finally make very sure the tube connecting the syringe to the nozzle is securely fastened - when I was cleaning the magenta the tube flew off the nozzle and ink sprayed everywhere!

My printer was only printing out the magenta color, with barely any other colors coming out. The self-clean printer nozzles option the printer has did little to unclog this. This product did the trick and dissolved the clogs in my Epson eco tank inkjet printer heads. There are multiple attachments and combinations of attachment you can use, but the only combo that worked for my printer was the yellow attachment with one end connected to the nozzle input and the other to the end of the syringe. I flushed all 4 nozzles and only used up no more than 1/4 of the solution, which can be saved for future use.However, be aware the using this product is not an immediate fix. After you flushed the printer heads, you have to wait at least a day for your printer to dry. After which, you need to run a deep cleaning cycle on your printer to get all the colors to show up again.

My epson 3760 sat idle for a long time so when I turned it on again, the printhead moved busily but no ink was dispensed...blank white paper. Used this product as directed for flushing nozzles and a bit more flushing followed by 2 cycles of 3 printhead cleans and I was back in business. In between each cleaning check the test page to see if the lines look good. And if you get to three cycles in a row and still have gaps on the test page, wait a day/ overnight before cleaning. Otherwise too many cycles in a row becomes counterproductive e.g. clogs nozzles even worse. Once cleaned and print quality is improved, print a minimum of a few pages weekly to keep from clogging. This is specific to the ecotank printers. Had more than half of the bottle left after generous flushing...but hopwfullu won't need it!

My Brother printer sat for literally years and when I replaced the ink it didnt print anything at all. Tried running the cleaning program several times. Still not a speck of ink on the paper. Got this cleaning solution, ran a syringe full in each color and the black, got the colors back immediately. Had to run a second syringe through the black to get it to print completely but now it prints like new. Thought I was gonna need a new printer but glad I tried this much cheaper solution. Still plenty of solution left for 2 or more cleanings.