Meinl Make Your Own Cajon Kit with Snares - MADE IN EUROPE - Baltic Birch Wood, Includes Easy to Follow Manual (MYO-CAJ)

As an experienced carpenter this was relatively simple. Pieces were all precut & ready to assemble. It’s still in construction process but I know it will turn out as desired. I’ve compared my assembly to that of same items in music stores & I’m even a bit better as I really pay attention to detail.Only complaint is the way the pieces are cut & have dado cuts for pieces to fit & create the box doesn’t allow for the box to totally sit even on the floor as there is a tiny rocking. Now I used corner clamps on all corners, insured my angles inside were spot on but the way it was originally cut doesn’t allow for a ‘perfect’ sit.I checked similar models of same company in music stores to see that they had the same issue so it has to be in the dado cuts, possibly not deep enough or exactly on but it wasn’t a big deal as it will work as expected.And I get to finish it how I want.I’ll be getting another as I’m creating a music room for when my grandkids come over. I have the canon, keyboards, acoustic & electric guitars, mics, tambourine, Jews harp, & harmonicas.

This was my first project with wood. I have some metal shop experience but had never built anything out of wood before, so this was to be a learning experience and hopefully have a working cajon at the end.TAKE YOUR TIME. This kit takes a while to build when you do it properly (several days). You want everything to dry nice and square. Luckily I did this part well. In terms of gluing everything, the instructions do a good job. Make sure everything fits well before gluing.The snare is a tricky part if you're concerned about sound. How tight do you want it, because you can't really change it once you put the front plate on. But you can't test the sound until you put the front plate on. I went with a tighter sound by moving the snare a little closer to the front plate. However, after finishing the cajon, I wanted more snare. I got a long screwdriver to losen the snare from the hole in the back and put a penny between the wood and the snare mount. That helped, but I think I could have used a nickel and gotten better sound.The last part of screwing the front plate on is where I started having problems. I followed the hole diagram very closely and counter-bored my holes. However, the corner holes line up exactly with the gap between wood pieces. Thus those screws don't make any contact with wood (and consequently just fall out). I drilled the holes before I glued those wood pieces so I didn't realized the problem until it was too late. I ended up screwing at a large angle to hit the wood sideways and dremeling the screw heads down smooth. Not a good solutions, but I didn't want to buy a new kit.As for finishing, I went with a dark mahogany stain and a polyurethane seal. Once again this was my first time with wood, so I learned a lot with this step and will do a much better job next time. I did two coats of the stain. Definitely need to sand the whole face down. I sanded the edges smooth (since they won't be perfect from gluing), and you can tell one section where the sanding was very different. Also definitely need to wipe up the excess stain on the wood. I have a few places where you can see the stain was dripping.I went with a gloss polyurethane finish. I wanted this to be water resistant so I went with that option. I did two coats, but a third would have really filled in the divots in the finish.A note on the front plate: I did a single coat of the stain and of the polyurethane on the front plate and I'm glad I did. The stain was fine, I just wanted a lighter front. But the polyurethane is heavy and I definitely noticed a big difference in sound after the polyurethane set. It sealed it up too good. I get great bass because of it, but those rich highs and snare are more muddy and subdued.The sound is about what you would expect for a $50 kit. It's not great, but it's not terrible. Could probably use a bass partition (which you could do yourself with another piece of wood), and definitely could use at least a second snare. The polyurethane definitely helped the bass but at the expense of the treble, so keep that in mind when you're deciding on the finish.

I built this cajon a couple of years ago. Mine just has the natural front. I don't think they had the others when I ordered it. I loved it then, and I still love it today! Putting it together was super easy. I didn't have straps like the ones shown in the picture so I just used a few small clamps and some books to hold it together while drying. After I assembled it, I had a friend paint a picture of a tree on one side and a quote on the other. Then I put a clear spray polyurethane coating on top of that. I haven't had any problems with chipping or anything. Sometimes a film builds up where I hit the face, but it cleans off pretty easily. I worked at a summer camp just after I built it and played it every day of the week for a whole summer, and it held up great! It has a good sound. You can get a decent bass towards the center of the face and higher sound at the top. I know you can get cajons that sound better than this one, but for the price, you can't beat it! Plus, you get the satisfaction of assembling it yourself, and throwing in a little of your own personality. I will say I wish I hadn't glued the front face to the body. It sort of deadened the sound a little, but I was able to make it work. Overall, I am very happy with my cajon. I might even buy the bongo cajon kit just for fun!

So far I have made 4 of these Bongo Cajons, which I am going to give away as gifts. I enjoyed making them, but in doing so, it did take a lot more time to do it right than I might have guessed when I first began work on the kits. Before you begin you need to make sure that you have the right kinds of clamps. For the sides I used four bar clamps, and when I glued the top down I used three strap clamps and once again I used the 4 bar clamps so that I could get a good tight fit. For glue I used a good quality wood glue and for a finish I used a quick drying polyurethane semi-gloss spray finish. I built up multiple layers of finish and lightly sanded in between coats. After the last coat of finish, I lightly sanded, and then used a very find steel wool on the finish and then polished the surface with an old t-shirt until all surfaces were extremely smooth.

Under features and details, it says two snares are in this kit. I received one snare. I messaged Meinl, and they said they would get back to me. But they did not.Assembly is nearly finished. It will be a gift for a 7 year old.

I bought it for a cousin whose father is a woodworker. they applied many more clamps than provided. the result was fantastic. My young cousin was thrilled. Then he took a wood burner to the face and put an amazing street scene on it. In fact, the kit may have sparked a father/son side business.