Mrcool DIY 12K BTU 4th Gen Energy Star Ductless Mini-Split Air Conditioner

It has been in service since I installed it almost 18 months ago. No issues whatsoever with the unit that is the18k model installed in a 24ft wide x 24ft long x 8ft tall (ceiling) garage in Glendale Arizona.I can confirm with this square footage having partially insulated walls and mostly insulated single garage door with a 2nd story above, the 18k unit is sized effectively. If you live in a lower temp environment you could get away with 12k but a hot vehicle pulled in to the garage. Will make the unit work for a few hours. In that scenario, this should be the proper size for most two car garages, regardless of the climate.Do your own research, of course. However, I did a great deal of research on mini split units all the way from Mitsubishi down to knock-off Chinese units. regardless of the manufacturer, most units are not rated for outside temperatures above 108°F, MrCool DIY’s are and they provide proof and testing on their site.So if you live in warmer climate, knock off Chinese units are not designed for high outside temperatures, and a majority of them will disable themselves when temperatures go above 105°f as they have an ambient temperature sensor on the outside unit that keeps them from overheating.I can confirm that this unit works effectively at Arizona desert temperatures over 120°f. Of course there is a large efficiency lost at that temperature but the ratings provided by the company prove this unit is more efficient than brands three times the cost.In fact, I can’t find a mini split unit on the market regardless of cost that has the same efficiency at temperatures over 115.°f.Yes, someone that is a home DIYer can install this unit themselves.However, I highly recommend you hire an electrician to run your disconnect.. everything else most DIYers should and can do. I know (and can look up) NEC and local codes. But if you cause an electrical fire by a faulty install, good luck getting a payout from your homeowners insurance. Same story if you sell your home with the unit attached and it wasn’t installed to code. And yes, running your disconnect could cost anywhere from $300-1200, but that’s life.Some have stated these units leak. My unit has not lost efficiency and I’ve monitored monthly kilowatt draw since last year and it’s pretty consistent.I did hook up a manifold gauge, and the pressure is low based manufacturer spec for target super heat.However, I assume that it was a loss in the hose or possibly initial seepage on the quick connect (I didn’t leak check after install).I read low pressure/charge as a common theme with these quick connects. I have been told the line set is charged with R410a and so is the unit. However, if this is incorrect or there was a slight seepage while in the box or during initial connect, that would explain the current levels. It’s fractionally low and probably losing 15% efficiency. You can buy small one time bottles on the Internet to charge mini splits that come with a gauge, you can pick one of these up and I recommend you do, no HVACR-EPA license needed. I haven’t charged mine since I need to move my main house split unit and I’ll wait till I buy a full R 410a tank.When the temp is below 90° outside, keeping my garage at 78°, I barely see much change in my kilowatt usage total for my home. Results may vary.. However this unit is hugely efficientI also feel keeping the garage below 100° keeps heat ingress out of my house, thereby raising the efficiency of my main unit.@@NOTE: I am also using MRCOOL’s wall mount for the unit. The unit will produce a low frequency vibration, though it comes with rubber feet, which help with mid frequency, if you will attach this to your house, you will hear the unit running when the home is quiet. For me it’s only noticeable when it’s dead quiet in the house and I’m on that side. My guess have never been able to hear it. So I’m probably neurotic. lol

I thought the pre-charged refrigerant lines were well engineered. I was a little concerned about doing them without a torque wrench, but they pretty much have stoppers you can tighten to which makes it really nice. Be wary of buying the suggested amazon wall bracket as it doesn't give enough clearance to the back wall to bend the refrigerant lines in, you'll need a good 10-12" room to the wall you mount it to (the mr cool separately sold bracket give you plenty of room to work with). I'd say it took me about 15 hours (including taking time to go buy some parts/tools I didn't have), but I had a complicated line-set run than most people would. I think the unit iteslf and instructions were really good.

installed this unit in my 30X40 metal building with insulation. Here in south Texas it works great keeps it nice and cool in the hot summer.

Pretty easy to install. Works well initially. Hoping it lasts well.

I purchased this unit which is 36,000BTUs rated for 1500 sq ft for my 1200 sq ft shop. It was pretty easy to install though NOBODY would use a 1/2" conduit connection from the power supply to the condenser, so it should be a 3/4" connection. Other than the crap instructions and pictures, took about 2 days or 10 hours. I am VERY capable of doing this work and will say my 1st attempt at an AC unit of any kind. Bottom line it turned right on, blows cold air despite the poor fan speed and simply is incapable of keeping my shop below 87 degrees, even on some days when it is just above 80 degrees. I did 4 tests all starting around 97, 92, 87, 95 inside and 101, 96, 94, and 83 inside. I NEVER got a reading below 87 degrees in my shop even after running for over 24 hours straight through the night when the temperature outside fell into the low 70s each night. I think I would need 4 of these units to get the workable comfort level that I was expecting. It is too bad, I cannot return it a so I am out 2 days work and $3000. Don't make the same mistake!!!!

The unit showed up early, and although the box was punctured, the insides were fine. I took my time and read the installation manual about 8 times before starting. Not everything is covered in the manual, but was is in there is very well written and mostly easy to understand. Nothing in the manual about running tubing out the sides of the indoor unit, but one call to customer service confirmed it is set up to do that. (Why don't they explain that in the install manual?) I ended up running mine out the back.It would be nice if they explained how to actually attach the UV tape. It has no sticky back, so one is left to improvise. A little guidance would help. The drain hose they supply is very flimsy. I purchased the outdoor bracket from Amazon. JEACENT Outdoor Wall Mounting Bracket for Ductless Mini Split Air Conditioner Heat Pump Systems, Universal, 7000-18000 Btu Condenser.Otherwise, it as not hard to do most of the install myself (with a helper for last day), and it took 2.5 days total. Take your time, double check everything.UPDATE after 4 months. I am very pleased with my Mr. Cool unit. It's very quiet and hasn't increased my electric bill very much as far as I can tell. I've left it running for a month straight during this very hot summer in SC, and set at 76deg my shop is cold.

Easy install and works excellent!