VLAND Tail lights Assembly Fit for Toyota 86 2012-2020, Subaru BRZ 2013-2020, Scion FRS 2013-2016, Rear Lamps with Dragon Scales Dynamic DRL, Back light w/Sequential Turn Signal, Red

The product arrived quick, took around 2-3 business days. There was a slight error with the package where I was missing an item, but the seller was quick to solve the issue. Also if you have any questions about the product, the seller usually replies fast. The install is really simple, you can look on youtube for installation instructions. Took me half an hour to install everything. The product comes with 8 pin cables pre installed or with the 6 pin cables that you will need to attach for if you own a scion frs. I do recommend buying t tap connectors to make the installation a whole lot easier. The LEDs are relatively bright and they fit perfectly in the headlight assembly. Everything worked perfectly fine on the first try after I installed it, basically a plug and play product. With how smoothly everything went and the quality of the product when received, I will say this is definitely a 5 star product and seller no doubt.

Work like a charm super easy to install.

easy install, only hard part was removing bumper, but you can find lots of videos online for that. Installed on a 2014 Scion FRS. I used H11 bulbs that barely fit without the rubber stopper on the back plate for rain but were not recommended. I will order correct bulbs later on. Where I live there were no bulbs in any store that would fit, Walmart, Autozone etc you may only be able to order these bulbs online. Instructions are in Japanese but lots if vids online to help install. The only thing I could not figure out was to use the daylight LEDS automatically. I spliced into the Parking lights instead so have to turn those on to use during the day. Something they don't mention is the way the lights work for brights. There is a motorized mirror in the headlights. When you use brights the mirror inside flips to give you full bulb wattage. So these headlights are designed for single bulbs only. Your old bulbs will not work. The H11 bulbs I used were purchased online and had a specific ring before the bulb in order for the retaining ring to hold the bulbs securely. I also removed the clips from the plug in order to attach my lights since the connector is fitted for the specified bulbs.

Great set of tail lights! Keep in mind if you are in the N American market you will need to swap the two wires with green bullet connectors on it for proper function. I work at an accessory shop thats been around for 30 years so I took two extra steps at install 1) Grabbed some clear silicon and ran a small bead around the red lens and black housing joint for added moisture intrusion protection. 2) Bought and installed a GasketNinja kit on the tail light housings themselves. The replacement thickness of the gasket on these VLANDS out of the box are great, but mine came in pinched on a smaller section of the DS housing gasket, which would of been a seal issue. The GasketNinjas come with 3M black silicon for applying to the housing itself. Overall great combo and very impressed.

It was ok no lights work in it burns holes don’t recommend headlights look nice and all but hard barley see out them

The media could not be loaded.  looks amazing had to do a wire switch between green and yellow wire because direction light and drl were switchedNo need to cut any wires or break anythingPull apart green rubber until metal is exposed , try to pry 2 metals apart and have a mix of yellow and green wire like in pictureAfter that worked great

These lights are the best i have used. i had run valentis for a few years, and though i liked them as well, these just blow them out the water. retaining the OEM look of the 2017-2021, these also have sequential LED's as well!. The quality out of the box, and instructions included were spot on, and ready to configure to USDM spec wiring.I had an issue with one of them, and VLAND support took care of my problems ASAP. I highly recommend their product, they stand behind it and it shows.

They are supposed to be plug and play but when plugged in the DRL became the turn signal and the turn signal became the running light. Trying to find solution but it’s quite upsetting

Pretty good lights. They work like a charm on my 2013 FRS. One of the light was scratched when I received them but it's ok since it's under the light. Still sad to receive 600$ scratched lights.

The media could not be loaded.  So far so good.They fit perfect and they work great.I can't speak for the longevity of them but they are decent quality. Not quite OE feeling but they are not full of water like my OE ones and at this price I can't complain.I read reviews about needing to "rewire" these in order to work with the Canadian market model 86 chassis cars so, being a seasoned ricer and Broke Boi knockoff parts specialist, I had my soldering iron and assorted hardware ready for an afternoon of tedious work... upon opening the box I realized I just needed to unplug and switch two wires. The full install took maybe 15 minutes all I needed was one 8mm wrench.

Installed these on my 2014 FRS and I absolutely love them. I was able to install them with no troubles and I’m not a mechanic what’s so ever. I just used simple T-taps to tap the daytime running lights as well as the turn single into the original turn signal in the bumper. I’ve had them for 2 months now and haven’t had any issues with them so far.Summary:-Super easy install-fairly priced-bright led strip-no leaks-makes the car look 10x better

It came without light bulbs.I was gonna get it swapped to HID anyways but it was not so obvious to me that the bulbs weren’t included

Product fits perfectly on my 13’ FRS. Simple plug and play, takes 15min to install and is completely worth it.