Beko Genuine Tumble Dryer Heating Element

Great part which was easy to install. I had to buy the whole Heater Element even though the only part that had failed on the element was the NTC Thermistor, but price for an NTC Thermistor was £35 on its own. I have now sourced and obtained NTC Thermistors from China and can repair the failed Thermistor unit on your failed heater unit. My failed thermistor measured 364 Ohms, where the new Thermistor measures about 18000 Ohms, so the failed unit was telling the main control card that no heat was required so the Relays for heating were not being energised, so no heating in the Tumble Dryer, Most failed heaters are just the Thermistor failed, very quick and easy to replace,

My dryer had stopped heating. Had the usual noises but clothes would still be wet and cold.For around £30 I thought I'd give this a go. Easy to fit if you can use a screwdriver and follow a you tube video.Dryer is like new heating better than before and also has reduced cycle times as old one was slowly dying.Looks like they burn out after 2-3 years of regular use.Saved me about £250 and hassle of having a new one and old one taken away.No wiring required as all plug and play. Very easy.Beko usually only have 3 problems.1. Make sure lint filter and sensor are clean. (Clean after every cycle)2. Make sure condenser is clean. (Clens after 30 Cycles)3. Heater could have tripped or burnt out. (Push reset switch on back of heater)Having checked and cleaned the filter and condenser I had no other option.Opened the back and checked the trip switch but not tripped.So changed the heater and works great. Comes with the two thermostats installed with new trip switch.Try this before throwing out the old dryer. Save yourself some money.

Easy to install being a direct replacement for the original. Highly recommended and free, secure packaging.

This made my dryer work again. Pretty easy to fit (but loads of screws).A post mortem on the old one turned up that it wasn't actually the element that was bust, but one of the safety cutouts, but they are integral to this unit, so replacing the whole thing fixed it.

Good product

I bought as a replacement for the heater that had previously gone in my tumble dryer after 8 years.It was so easy to fit, literally just replacing like for like. Some bits a little more fiddly, so definitely do it when you are calm and have time to take your time.Just remember where you take things out of as there is no instructions, i had my own wee system as I went.Works perfect and have used several times a week with no issues so far.Much cheaper than a new tumble dryer.

My wife killed dryer and start looking for new one.I decided to look into it and try to sort without losing money and all that pain with new dryer.When trying to switch on dryer my fuse blows instantly and that was easy to google what it’s wrong with it.After watching vid on yt it was clear what I need to do to it’s check if element it’s toasted if not that something more serious.Take few minutes to unscrew back panel where element it’s located and after trying press reset button on it was clear what’s not working (reset button should jump back)After wrote down numbers from heating element I did research for new part, now before I go what happen I should say my original was 700w/1600w but Beko replaced that version with 900w/1600w and stop making original one.I find cheaper one on amazon and after buy 1 from seller (who send from amazon) I end returning as was wrong one...2nd one I buy from spare2go (Seller on amazon) and was correct one still toke a week to sorted out because of wrong one.Save yourself problem and buy from them.After part come toke me less then 10 min to replace it.Back panel have a multiple screws and there 3 different sizesTop cover only 3 screwsHeating element 3 screwsTo unplug element first need to take off 1 screw of connector then cut cable tie from back of machine connector it’s inside, both screw and tie located close to each other and need take a look from top to see, after that it’s easy to unplug otherwise will be hard to do it as it’s in small space.After that wire need go thru small hole with rubber ring one after another as both will not fit.And all done ✅Saved £££ and wife happy as dryer back to work.Forgot to mention on Beko site that part cost around £50 then it’s cheaper here.

Installed by professional and blew up in flames as soon as turned on faulty wires???