HARDELL Angle Grinder Dust Shroud 4.5/5 Inch, Angle Grinder Attachments, for Universal Angle Grinders(125MM)

good quality product but its a better fit for a 7" grinder. if you're using with a 4.5" angle grinder and you need to get close to something even with the lid that opens up you'll be too far away, Canada is closer. Don't buy this for a 4.5" angle grinder, its far too big.

I was worried about ordering this because of the bad reviews, but it works good! The only problem is that it does not have a shop-vac size attachment that fits a full size vac hose, its the size of a house vacuum hose. So you will need to figure that out. I have an attachment from the expensive 4" grinder dust shroud attachment that I have had for years that is fit onto so it worked for me. It works just as good as my 4" name brand/expensive model. So I think some of the bad reviews are user error.

We redid a set of concrete walls that had bulged and cracked due to water getting in and swelling the rebarb. The Mason was pretty good but it's not all that easy to get large 2 foot patched of concrete perfectly level. I got this tool to see what it could do and it came through perfectly.We hooked it up to a DeWalt 9 gallon shop Vacuum to control the dust and to my amazement there was zero detectable dust. The Blade cut into the concrete at about 1/32" per pass with light touch and about an 1/8" with a hard press. Very controllable for leveling out the concrete.So far we have done about three patched ot areas with each one about 2ft squared.No problems with level cutting and dust. I just bought another unit because the job is big and we don't know if it will last the whole way through. So far at this price and the results I am getting I am more than happy to buy an extra unit.

I have a 4” concrete grinding wheel on my cheap Menards grinder. That’s apparently a bad combo.What’s strange is that the clamp for the grinder attachment doesn’t seem to be designed for the diameter of the adapters. When clamped to the proper tightness to keep it in place, the entire dust shield is shifted off to one side. This would absolutely cause the plastic melting that some have experienced. I did not have a larger wheel, so didn’t have this issue.My particular wheel did not extend past the bristles around the shield. I had to press down a lot to get the wheel to even contact, and then it barely took anything off. After trying to trim down the bristles unsuccessfully, I ended up pounding them out with a hammer and screwdriver. This actually ended up working really well for me.The hose adapter doesn’t sit very well in the dust shield. So plan on that falling out a lot.After the above modifications, it worked quite well, minus the hose adapter issues mentioned. Even without the bristles, dust was almost all sucked up with my shop vac.So do I recommend this? Depends. If you just want to buy the cheapest one and are fine with heavily modifying it to work for you, have at it. If you want something that works out of the box? Move on and find another.

I must say it has earned its place in my toolkit with a solid 5 rating.First and foremost, my wife gave her stamp of approval on how well this item worked. She was concerned using a grinder in the house to remove tile mortar and this dust shroud did not disappoint in that regard.Setup was easy. I encountered no issues fitting it onto my grinder. Connections supplied also seamlessly connected to my shop vacuum. However, I did notice that I had to pay some attention to ensure that the vacuum hose stayed securely connected while using.One minor hiccup I encountered was the need to add some pressure to the top of the grinder during use to press down the ‘broom’ bristles to make floor contact. It took a bit of trial and error to find the exact pressure required, but once dialed in, the performance was exceptional.The dust shroud effectively contained ALL dust generated. I did have on a respirator, but I probably could have done without it.It gets the job done; I’m really impressed after reading quite a few negative reviews on like products.

Seemed OK out of the box, but when I tried to mount the shroud on an angle grinder I found a problem. The mounting hole on the shroud, where it is mounted on the angle grinder, was off center, so a 4-1/2" grinding wheel hit the side of the shroud, making it imposible to mount the grinding wheel and the shroud unusable. I returned the product and will purchase another from a different manufacturer.

Worth its weight in gold! Very effective at keeping dust at bay when grinding concrete.

Had zero issues with dust when hooked up to my garden hose. My only problems were the water valve did not stop the water completely and the collar was too small for the 7" grinder. I used my 4.5" grinder with the 7" wheel and let the smoke out of it.

This little tool works wonders!Works great with a shop vac, just leaves a little bit of sand dust behind and helps keep the house clean

No ofrecen nada más de lo que anuncian… pero al usar te das cuenta porque es que funcionan. En humeo o en seco funcionan para lo que fueron hechas.

Fait sur mon grinder de canadien tire ( mastercraft). Plusieurs adapteurs pour l'installation et pour les balayeuse ! Recommande à 100%

Todo bien con esta compra, es mucho más fácil trabajar sin tanto polvo en la cara

It works very well