BIQU MicroProbe V2.0 Auto Bed Leveling Sensor Upgrade Kit with Metal Bracket/MK8 Nozzle, High Precision for Ender 3/V2/BIQU B1/H2 Extruder Voron 3D Printer Octopus V1.1/Pro Manta/SKR Mini E3 Board

Works great! Super easy to configure and calibrate

Installed on my E5 Plus. Now it can level the bed

BLtouch is a great product but instructions for 32 bit board need to be updated. I emailed the seller my discoveries who in turn will notify the ANTCSLABS.I have spend many hours trying to figure out this setup, I ended up figuring out that instructions are quite misleading and they would drive you off the wall.first of all, Creality BLtouch kit works fine, as far as hardware installation, but configuration of BLtouch on 4.2.7 motherboard is grossly inaccurate.Here is what I discovered by trial and error and watching bunch of youtube videos, many of them did not quite cover the topic correctly.First of all, you will need an micro SD card to save the settings on 4.2.7 motherboard, there is not much room left on EEPROM once all of the features are enabled and you will need to save them to micro SD card or when you power off your printer all will be lost. You will need to re-calibrate the Z settings again. If you forget to punch in Z offsets if the printer was powered off you will be printing a few millimeters up in air. Don't ask me how I know./// How to configure BLtouch after the device is physically installed and wired up///==================================================================Unplug the USB cable if connected to the computer, this prevents the 3D printers receiving the power to its motherboard.Verify BLTOUCH operation and correct installation==================================================================Verify that BLtouch is working correctly by moving the nozzle assembly at least 150 mm above the bed. We will issue auto home command and we need some vertical space so that can turn off the printer power if BLtouch is not stopping downward movement when its probe is touched.Via the printer menu select Prepare -> auto home – printer will start the auto home process and the nozzle will start moving down and BLtouch will extend (lower) its probe.As the nozzle assembly is moving down gently touch the BLtouch probe, the nozzle should stop, then resume downward movement. Touch the probe again for the second time and the nozzle will stop moving permanently. That means that BLtouch is wired correctly and it will stop when the probe touches the bed.Please note: Be ready to turn off the printer power if when touching the BLtouch probe the nozzle is still moving down! In that case you need to check the Bltouch for correct wiring to the motherboard.How to calibrate the Z offset==================================================================Via the printer control knob do the following steps:Select ControlThen restore failsafeAnd store settings.This erases any settings that were previously configured so we start with a blank slate. This is a very important step! If some old Z offsets are still in EEPROM and you start to configure printer you could potentially have the nozzle hit the bed because of old Z offsets were not erased. So, restore the settings to failsafe!note: make sure you have the micro SD card inserted.Auto home the printer==================================================================select prepareSelect Auto home and wait for process to completePrinter will auto home where it thinks the Z axis is. Please note; now there is a few millimeters difference because BLtouch is a few millimeters above the nozzle. This is by design to prevent BLtouch needle to hit the printed object.That is why we have to measure that difference and write it down to be used later.To determine Z offset==================================================================select Prepare,Then move axisThen move ZSelect 1mm and start moving the nozzle down towards the bedWhen you get close to the bed change to 0.1 mm incrementsInset a sheet of A4 paper on print bed (paper is 0.2 mm thick)keep lowering the nozzle via “move Z” slowly with one hand and keep moving the sheet of paper back and forth until there is slight resistance with other hand.You should be able to move the paper back and forth but with slight resistance.Now, stop and write down the value. The value in this image is my value, your value will be different!This will be a negative value somewhere between 2.5 and 4 mm as BLtouch probe is typically that much higher in relationship to the nozzle, and this value varies from one printer to another.This is the value that we will need to input into Z offset in later steps.To prevent accidentally scratching of the bed with the nozzle select prepareThen auto homeConfigure probe Z offset==================================================================select controlThen bed levelingThen probe Z offsetAnd put the value that you have written down for Z offset that you measured in previous steps.The value will be in negative (minus) so for example, -003.2 mm)The value should be typically between 2.5 and 4 mm with original creality Bltouch bracket.Finally, select store settings to save your Z offset!Exit the menu to the top and then verify that settings are correct for Z offset!Your value should be there!Bed leveling==================================================================Select controlThen Bed levelingThen select level bed The process will probe 9 pointsOnce that is done auto leveling is completed.Modify Cura settings for BLtouchIn Cura –select settings -> printer -> manage printersClick on machine settingsAnd add under Start G code:G29 ; (Auto Level / BLtouch mesh)M500 ; save the mesh EEPROMClick close and close again.Do a test print from cura!adjust the Z offset if neededgood luck!

It is a very good probe, but it is designed for a very specific use case and is probably not compatible with your tool head, so don't make that mistake

If you don't already know EXACTLY how to install this do not bother. I can't believe there are so many good reviews. Maybe it's a good sensor, but that's irrelevant if you have to be an electronics expert to figure out how to install it. The wires are are too short and crossed from one end to another. And you are really on your own to figure out, through trial and error, how to get it to work for whatever printer/board combo you have. I have spent days trying to figure this thing out. There must be 100 different videos on installing this on any given combo and not two of them seem to agree. This is not a product ready for sale, it is a collection of parts that theoretically can be put together by an expect. This thing has been on the market for years, is seemingly a common printer upgrade, and there still isn't comprehensive, correct, easy to follow instructions anywhere. Sure it can be used on a variety of different boards and printers, but as long as this thing has been out that's no excuse for the phoned-in "instructions" provided.

You have to know what you're doing or else you'll end up in my boat with a brick until solved. But that's on me, I take full responsibility. Now that I have it up and working properly, the mesh it's building is super accurate!

Tech support took very long and getting back to me and they never solved my problem they only had short few sentence answers I heard that big tree had great tech support but definitely not my experience even though it could be a configuration problem I have they made no attempt to help me with it I sent them copies of printouts and just very lame I would say. And additionally it was their board and their unit.

I have used this and the 3d touch. Both get the job done. This one feels of higher quality though, and the probe snaps back satisfyingly, plugs securely, love it.