1-Pack Led Panel Ceiling Light Fixtures 24w 5730 SMD Circle Annular Round Replacement Board Bulb White 6500K (White)

Bought the 24w White LED panel to replace 12" T9 fluorescent bulb.The LED ceiling panel with ballast and hardware came in a flimsy Amazon bubble envelope. Part of the metal was warped during shipping but I was able to shape it back into a flat surface. Suggestion: use a box for shipping! The hardware included are the magnets and screws necessary to mount into existing metal ceiling fixture. I removed the existing T9 fluorescent bulb and ballast along with the metal clamps holding in the T9 bulb. Then affixed the assembled LED panel with new ballast. Wiring was very simple also. Using the provided 2-way spring connector connected the LED wires to the wires from the ceiling. I had to strip the ceiling wires for a clean connection (so you may need pliers to do this for your wires). I used red for positive and blue for negative from the LED panel, my ceiling wires are white (neutral) and black for hot (positive). The spring connector is not marked but just match up each end in the spring connector.The LED is very bright. Way brighter and more of a blue than a yellow light. Overall, I'm very happy with the ease of installation. Great value!

This replaced an 8" fluorescent bulb that burned out. All you have to do is remove the old starter, splice in the LED driver, remove any bulb holders for the old bulb, and this snaps in with the included magnet standoffs. It's a 10 minute affair. The result is 2-3 times brighter that the old fluorescent bulb. My fixture has a translucent plastic lamp cover that fit pretty tight to the base. So I drilled a series of 1/4" holes around the base of the plastic lamp cover where they wouldn't be seen to ventilate the fixture just in case. The lamp is now much brighter with a warm glow that works well in the utility room where it's installed. The provided LED driver has mounting holes but I just stuck it to the base of the lamp with velcro since it's very light. Works great. I only wish we could make LED products in the USA so I could buy American!

Update- this is my second one and it's in better shape than the first that arrived bent. Did bother with the magnets this time just used some small nuts and bolts I has around. Works excellent. No more FL bulbs for meI had a nice looking (though florescent) light fixture for a laundry room that had two rings, one about 12" and the other 8". I also wanted to put an auto switch on the wall and that was tough to do with FL lights (due to the ballast I guess). Plus the lights were getting worn out and we that crummy FL color. I ordered this and used the old fixture housing that was still in nice condition . The only issue was tearing out the little clips that held in the old FL bulbs that were riveted into the housing. The magnets worked out but were a little fragile. I dropped the whole unit and two of them shattered but they gave two extras but one of those broke but it still stays in place ok.The packaging could have been better which is why I gave them a 4. The LED light itself is very thin and the post man actually FOLDED it to stuff it in my mailbox. I was able to flatten it out some and there is a plastic cover it anyways. all the LEDS pods work also.But the light itself works fine. The color is warmish- better than FL anyways... and I also bought a motion detected switch and now the whole thing turns on when you enter the room and stays on for 1/5/15 minutes. (another amazon part that cost more than this light) ..

The LED panel was purchased to replace the light in my kitchen. It was an easy install once I removed the previous panel that was mounted in the fixture. The light from the panel is almost a bluish white and took a little time getting used to but definitely does the job intended. The mounting magnets worked well except one of the screws were off and gave me trouble. All in all it was worth the money and hopefully will light the kitchen for some time.

relatively easy to install / adapt to old torcherie lamp. Same light output and color as our old flourescent tube. Removed ballast and ring adaptor. Attached this with wire tie anchors and wire ties.06-03-2024 updateLast purchased on Sep 8, 2022Lasted a year and 9 months, bad LED SMD chip.Taking out 2 stars. Not enough longevity. Low quality components?

Great product and it revived my kitchen ceiling light. I might need clean the grease covered plastic cover to get the 2400 lumen :) The LED driver is a little bit flimsy and hope it can last longer. I made a stupid mistake, trying to pull the ballast out of the housing rather than directly cutting and stripping the incoming wires of the ballast as the manual suggested, and it became a fiasco....Just using the wire connector in the kit instead using wire nuts from the old housing. A 10 minute work became 2 and half hours.

I purchased and installed this light in November. It's now April and it has stopped working. We checked all other connections. I'm disappointed in the quality of this product.

I've replaced about half the florescent units in my basement with these, allowing me to reuse the fixtures without having to replace them. And they're brighter than the round bulbs with a cleaner light.